Recalls: 1994 - CHEVROLET - C10

---

Recalls

• NHTSA Campaign ID Number: 06E060000 - EXTERIOR LIGHTING
  Recall Date: 06/29/2006

  Summary:
  CERTAIN AAI MOTORSPORTS COMBINATION LAMPS SOLD AS REPLACEMENT LAMPS FOR USE ON THE ABOVE LIST PASSENGER VEHICLES. COMBINATION LAMPS NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, ¿LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.¿
  
  Manufacturer that filed the Recall:
  TOYOTA MOTOR NORTH AMERICA, INC.
  
  Consequence:
  LACK OF AMBER SIDE REFLECTORS IN THE LAMPS WILL DECREASE LIGHTING VISIBILITY TO OTHER DRIVERS AND MAY POSSIBLY RESULT IN A VEHICLE CRASH
  
  Remedy:
  AAI MOTORSPORTS WILL NOTIFY OWNERS AND REPLACE THE LAMPS FREE OF CHARGE. THE RECALL BEGAN ON AUGUST 1, 2006. OWNERS MAY CONTACT AAI MOTORSPORTS AT 909-923-9188.

• NHTSA Campaign ID Number: 93V152000 - SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES
  Recall Date: 09/21/1993

  Summary:
  THE BRAKE PEDAL PUSH ROD RETAINER IS MISSING, MISPOSITIONED OR NOT PROPERLY SEATED.
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  BRAKE PEDAL PUSH ROD PROBLEMS CAN CAUSE THE STOP LAMPSWITCH AND THE BRAKE BOOSTER PUSH ROD TO DISCONNECT FROM THE BRAKE PEDAL,RESULTING IN LOSS OF BRAKE OPERATION, AND A VEHICLE CRASH COULD OCCUR WITHOUTPRIOR WARNING.
  
  Remedy:
  INSPECT VEHICLES TO ASSURE THE BRAKE PEDAL PUSH ROD RETAINER IS PRESENT AND FULLY SEATED IN ITS CORRECT POSITION.

• NHTSA Campaign ID Number: 93V216000 - SEATS
  Recall Date: 12/30/1993

  Summary:
  THE SEATS HAVE BEEN ASSEMBLED WITHOUT BOLTS THAT CONNECT THE UPPER SLAVE HINGE TO THE SEAT BACK FRAME, OR WITHOUT BOLTS THAT CONNECT THE SEAT TO THE SEAT ADJUSTER. IN EITHER CASE, THE VEHICLES FAIL TO CONFORM TO FNVSS NO. 207, "SEATING SYSTEMS."
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  THE MISSING BOLTS MAY CAUSE THE DRIVER'S SEAT TO BECOMELOOSE AND IN A SUDDEN STOP OR ACCIDENT MAY SUBJECT THE OCCUPANT TO INCREASEDRISK OF INJURY.
  
  Remedy:
  DEALERS WILL INSPECT SEATS FOR MISSING BOLTS AND INSTALL BOLTS IF REQUIRED.

• NHTSA Campaign ID Number: 94V060000 - SUSPENSION:FRONT:CONTROL ARM:LOWER ARM
  Recall Date: 04/13/1994

  Summary:
  TRUCKS WERE ASSEMBLED WITH THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TIGHTENED BELOW THE SPECIFIED TORQUE. LOW TORQUE ON THIS NUT MAY ALLOW THE ATTACHMENT BOLT TO LOOSED AND SUBSEQUENTLY FATIGUE AND BREAK. THE BOLT BREAKAGE CAN CAUSE THE LEFT HAND CONTROL ARM TO SEPARATE FROM THE FRAME.
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  IF THIS OCCURS, A LOSS OF VEHICLE CONTROL AND A CRASH COULD RESULT.
  
  Remedy:
  DEALERS WILL TIGHTEN THE LEFT-HAND LOWER CONTROL ARM TO FRAME REAR NUT TO THE PROPER TORQUE SPECIFICATION.

• NHTSA Campaign ID Number: 94V212000 - VISIBILITY:WINDSHIELD
  Recall Date: 11/02/1994

  Summary:
  THE WINDSHIELDS WERE INSTALLED WITH INCORRECT WINDSHIELD OPENING PINCH-WELD-FLANGE PRIMER. THIS PRIMER WILL NOT PROPERLY ETCH THE PAINTED SURFACE OF THE FLANGE, ALLOWING THE WINDSHIELD TO SEPARATE FROM THE VEHICLE DURING A COLLISION. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 212, "WINDSHIELD MOUNTING."
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  CONSEQUENCE OF NON-COMPLIANCE: THE SEPARATION OF THE WINDSHIELD FROM THE VEHICLE DURING COLLISION INCREASES THE RISK OF INJURY FOR ALL PERSONS INVOLVED.
  
  Remedy:
  DEALERS WILL REMOVE THE WINDSHIELD AND REINSTALL IT USING THE CORRECT PRIMER.

• NHTSA Campaign ID Number: 95I005000 - ENGINE AND ENGINE COOLING:ENGINE:DIESEL
  Recall Date: 02/14/1996

  Summary:
  VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS, VANS AND MOTORHOMES EQUIPPED WITH ELECTRONICALLY FUEL INJECTED 6.5L DIESEL ENGINE. THIS IS NOT A SAFETY RECALL IN ACCORDANCE WITH FEDERAL REGULATION PART 573. HOWEVER, IT IS DEEMED A SAFETY IMPROVEMENT CAMPAIGN BY THE AGENCY. THE CAMPAIGN WILL IMPROVE THE OVERALL DRIVEABILITY OF THESE VEHICLES.
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  CERTAIN VEHICLES CAN EXHIBIT SOME DRIVEABILITY CONCERNS SUCH AS POOR THROTTLE RESPONSE, STALLING, MISFIRE, POOR HOT OR COLD STARTING, EXTENDED CRANKING OF A HOT ENGINE, OR STALLING AFTER START. TRUCKS WITH MANUALTRANSMISSIONS CAN EXHIBIT POOR ACCELERATION FROM START OR COULD STALL DURING DECELERATION.
  
  Remedy:
  DEALERS WILL INSTALL SOME RECENTLY DEVELOPED ENHANCEMENTS WHICH WILL IMPROVE THE OVERALL DRIVEABILITY OF THESE VEHICLES.

• NHTSA Campaign ID Number: 95V241000 - SEAT BELTS:FRONT
  Recall Date: 01/02/1996

  Summary:
  IF BOTH THE LAP-BELT AND SHOULDER-BELT ENERGY MANAGEMENT LOOPS ON THE FRONT SEAT BELT ASSEMBLIES RELEASE AT OR NEAR THE SAME TIME, ACCELERATION FORCES CAN CAUSE THE BUCKLE RELEASE MECHANISM TO ACTIVATE AND ALLOW THE BUCKLE TO SEPARATE FROM THE LATCH.
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  IF THE BUCKLE RELEASED, THE SYSTEM WOULD FAIL TO PROVIDE ADEQUATE OCCUPANT RESTRAINT PROTECTION.
  
  Remedy:
  DEALERS WILL REMOVE THE STITCHING THAT CREATES THE ENERGY MANAGEMENT LOOP IN THE SHOULDER BELT(S).

• NHTSA Campaign ID Number: 95V242000 - SEAT BELTS:FRONT
  Recall Date: 01/02/1996

  Summary:
  THESE VEHICLES WERE BUILT WITH FRONT SEAT BELT SYSTEMS WITH NO ENERGY MANAGEMENT LOOPS AND MAY NOT MEET THE HEAD INJURY CRITERIA REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION."
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  IN THE EVENT OF A VEHICLE CRASH, THE OCCUPANTS OF THESE SEATS MAY NOT BE PROPERLY RESTRAINED.
  
  Remedy:
  DEALERS WILL REPLACE THE RETRACTOR PORTION OF THE SEAT BELT ASSEMBLY(S) WITH ONE HAVING THE NEWLY DESIGNED ENERGY-MANAGEMENT TWIN-LOOP SYSTEM.

• NHTSA Campaign ID Number: 95V246000 - SEATS
  Recall Date: 01/02/1996

  Summary:
  THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLE COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.
  
  Remedy:
  DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

• NHTSA Campaign ID Number: 96E010000 - SEATS
  Recall Date: 03/29/1996

  Summary:
  THE SEAT RECLINER TO SEAT FRAME ATTACHING BOLTS ON THESE VEHICLES COULD LOOSEN, FATIGUE AND FRACTURE, ALLOWING THE SEAT BACK TO SUDDENLY RECLINE.
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  IF THIS WERE TO OCCUR TO THE DRIVER'S SEAT, THIS COULD RESULT IN A SUDDEN LOSS OF VEHICLE CONTROL INCREASING THE RISK OF A VEHICLE ACCIDENT.
  
  Remedy:
  DEALERS WILL REMOVE ALL FOAM AND/OR FABRIC SANDWICHED BETWEEN THE RECLINER ASSEMBLY AND THE SEAT FRAME, INSTALL WASHERS BETWEEN THE SEAT RECLINER AND THE SEAT FRAME AT EACH ATTACHMENT POINT, AND INSTALL NEW ATTACHING BOLTS TORQUED TO A HIGHER SPECIFICATION. THESE CORRECTIONS WILL BE MADE TO BOTH THE DRIVER'S AND PASSENGER'S SEATS.

• NHTSA Campaign ID Number: 98V150001 - VISIBILITY:WINDSHIELD WIPER/WASHER
  Recall Date: 02/11/1999

  Summary:
  VEHICLE DESCRIPTION: LIGHT DUTY PICKUP TRUCKS AND SPORT UTILITY VEHICLES, 2 AND 4-WHEEL DRIVE. SOLDER JOINTS NEAR THE WIRING HARNESS CONNECTOR CAN CRACK CAUSING THE WINDSHIELD WIPERS TO WORK INTERMITTENTLY.
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  THIS CONDITION CAN RESULT IN INOPERATIVE WIPERS, REDUCING A DRIVER'S VISIBILITY, AND INCREASING THE RISK OF A VEHICLE CRASH.
  
  Remedy:
  DEALERS WILL REPLACE THE WIPER MOTOR CIRCUIT BOARD AND COVER.

• NHTSA Campaign ID Number: 99V025000 - SERVICE BRAKES, HYDRAULIC:SWITCHES:BRAKE LIGHT
  Recall Date: 02/08/1999

  Summary:
  VEHICLE DESCRIPTION: PICKUP TRUCKS, CREW CABS, UTILITY TRUCKS AND SPORT UTILITY VEHICLES. THESE VEHICLES WERE BUILT WITH THE POLARITY OF THE WIRING FOR THE ZERO ADJUST BRAKE SWITCH REVERSED FROM WHAT WAS SPECIFIED ON THE SWITCH DRAWING. WITH THE REVERSED POLARITY, THE CONTACTS IN THE BRAKE SWITCH CAN WEAR OUT PREMATURELY. THE BRAKE SWITCH WILL PERFORM NORMALLY UNTIL THE BRAKE SWITCH CONTACTS WEAR OUT, RESULTING IN LOSS OF THE BRAKE LAMPS WITHOUT ANY WARNING TO THE DRIVER.
  
  Manufacturer that filed the Recall:
  GENERAL MOTORS CORP.
  
  Consequence:
  THIS WOULD FAIL TO WARN A FOLLOWING DRIVER THAT THE VEHICLE IS BRAKING AND COULD LEAD TO A CRASH.
  
  Remedy:
  DEALERS WILL REPLACE THE BRAKE SWITCH AND REVERSE THE WIRING.